Smart Home Wiring & Integration in Newmarket

Smart home wiring projects in the Newmarket range widely. A retrofit of 10 smart switches plus a smart lock and thermostat runs $3,000 to $6,000. Whole-home structured Cat6A wiring during a renovation costs $5,000 to $15,000. Full automation with smart switches, motorized shades, audio, and security comes in at $15,000 to $40,000. Premium Control4 integrations range from $40,000 to $200,000. RenoHouse provides free, itemized quotes.

Structured wiring is a centrally-organized network of Cat6A Ethernet, fiber optic, in-wall HDMI, coaxial, and speaker cables routed from a wiring closet to every room. It guarantees fast, reliable connections for streaming, video conferencing, smart cameras, and gaming — none of which Wi-Fi alone can match in a multi-floor Newmarket home. It is best installed during a renovation or new build before drywall.

Cat6A is the right choice for most homes today — it supports 10 Gbps up to 100 metres and works with all current and near-future smart home gear. Cat6 is acceptable for short runs but tops out at 1 Gbps over longer distances. Fiber optic makes sense only for very long runs (over 100 metres), home offices with serious bandwidth needs, or future-proofing high-end builds. RenoHouse defaults to Cat6A unless you have a specific reason otherwise.

Yes. RenoHouse is an experienced installer of Lutron Caseta and RadioRA 3 smart lighting and shading. For Control4 we partner with certified Control4 dealers who handle the programming and ongoing service contract while we handle the structured wiring, low-voltage prep, and electrical work. This gives you the best price on Control4 hardware without paying integrator markup on cabling.

Many Newmarket homes built before 1990 lack a neutral wire at switch boxes, which limits the smart switches you can use. Lutron Caseta is the gold standard for no-neutral applications and works reliably in 95 percent of older homes. Inovelli, GE Cync, and select Leviton Decora Smart models also work without a neutral. We confirm wiring during the estimate.

We design Wi-Fi coverage with a mesh system sized to your floor plan and number of devices. For a typical 3,000-square-foot Newmarket home we recommend a 3-node Eero Pro 6E or Ubiquiti UniFi U6 setup wired back to a central switch via Cat6A — not wireless backhaul, which slows everything down. We test signal strength and throughput in every room before signing off.

Yes. Power-over-Ethernet camera wiring eliminates the need for power outlets at each camera location and uses a single Cat6A run for both data and power. RenoHouse installs Reolink, Ubiquiti UniFi Protect, and Nest cameras, terminating into a network video recorder (NVR) or cloud service of your choice. We pre-wire conduit during framing on new builds for clean future expansion.

Yes. We install Lutron Serena and Hunter Douglas PowerView motorized shades, wired to a central hub for integration with Lutron Caseta or Control4 lighting scenes. This lets you trigger 'movie mode' (close shades, dim lights, turn on TV) with one tap. Battery-powered options are available for retrofit projects without conduit access.

Standard practice on RenoHouse smart home projects is to pull at least 2 Cat6A cables to every TV location, 1 Cat6A to every desk and bedside table, conduit chases between key rooms for future upgrades, and structured cabling backbone to a central rack with at least 25 percent spare ports. This ensures you can add cameras, access points, or new devices over the next 15 years without opening drywall.

Low-voltage structured cabling does not require an ESA permit in Ontario. Smart switches and high-voltage work (replacing a regular switch with a smart switch) are treated as standard electrical work and may require a minor ESA permit. RenoHouse pulls all required permits and includes them in the quoted price.

Outdoor outlets require weatherproof GFCI-protected receptacles installed in code-compliant boxes. We run dedicated circuits from your panel to strategic outdoor locations — patios, garages, sheds, and garden areas. All installations meet ESA requirements and include proper grounding for safety.

A panel upgrade (typically 100A to 200A) involves replacing the main breaker panel, upgrading the service entrance cable, and potentially upgrading the meter base. The process takes 4–8 hours and requires a temporary power shutoff. We coordinate with your local utility and ensure ESA inspection approval.

Hot tubs typically require a dedicated 240V/50A circuit with GFCI protection. We run the wiring from your panel to the hot tub location, install a disconnect switch within sight of the tub (code requirement), and ensure everything passes ESA inspection. Planning ahead during deck construction saves on installation costs.